	ITE RAIDExpress 133 Mandrake Installation Guide and Release Note
				
				April 25, 2003
				    Mark Lu

			(C) Copyright 2003 ITE, Inc.


1. Component Name(s) and Version #:
===================================
Components	: For Mandrake 9.0
Kernels Tested	: 2.4.19-16mdk
Driver Version	: v1.3
Release Date	: April 25, 2003


2. Files Listing (in linux directory)
=====================================
   redhat73.txt			RedHat 7.3 installation guide
   redhat80.txt			RedHat 8.0 installation guide
   mandrake90.txt		Mandrake 9.0 installation guide
    | 
    |
    +- md90			Mandrake 9.0 directory
    |  |- iteraid.o		Driver module for Mandrake 9.0
    |
    +- rh73			RedHat 7.3 directory
    |  |- modinfo		Module info file
    |  |- modules.cgz		Compressed driver modules
    |  |- modules.dep		Module dependence file
    |  |- pcitable		IT8212 pci info
    |  |- rhdd-6.1		Driver disk label
    |  +- iteraid.o		Driver module for RedHat 7.3
    |      
    +- rh80			RedHat 8.0 directory
       |- modinfo		Module info file
       |- modules.cgz		Compressed driver modules
       |- modules.dep		Module dependence file
       |- pcitable		IT8212 pci info
       |- rhdd-6.1		Driver disk label
       +- iteraid.o		Driver module for RedHat 8.0

        
3. Revision History
===================
v1.0	01/16/2003		First release
v1.1	02/07/2003		Fixed module install problem
v1.2	02/18/2003		Fixed interrupt service routine
v1.3	04/25/2003		ATAPI support. 
				Fixed performance issue under Red Hat.
 

4. Installation Guide
=====================

   4.1. **** Installing IT8212 Linux Driver into an EXISTING SYSTEM ****
   
   01. Boot linux system and login as root.
   02. Copy the IT8212 driver module (/linux/md90/iteraid.o) to any 
       directory you want, then go to that driectory.
   03. You can test out the module to ensure that it works by the following
       commands:
       
       # modprobe sd_mod
       # modprobe sr_mod
       # insmod iteraid.o
       
       To ensure the modules has been loaded successfully, you can check
       the driver module loading status by using the "dmesg" command.
       
       # dmesg
       
       Then you will see the following messages.
       
       ...
       ...
       Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
       SCSI device sda: 120103200 512-byte hdwr sectors (61493 MB)
       ...
       ...
       
   04. The following commands is only for reference.
   
       Now you can create the partition when the IT8212 driver is installed.
       
       # fdisk /dev/sda
       
       If you create two partitions on /dev/sda, for example /dev/sda1 and
       /dev/sda2. Then you can use the mkfs to make the filesystem.
       
       # mkfs /dev/sda1		<-- Make /dev/sda1 as ext2 filesystem
       # mkfs -j /dev/sda2	<-- Make /dev/sda2 as ext3 filesystem
       
       After this you can create two directory for mount point. For
       example:
       
       # mkdir /mnt/hd0
       # mkdir /mnt/hd1
       # mount -t ext2 /dev/sda1 /mnt/hd0/
       # mount -t ext3 /dev/sda2 /mnt/hd1/
       
5. The note for using ATAPI CD-ROM
===================================

   01. If you want reading the data disk, just insert the disk into CD-ROM,   
       then mount as iso9660 file type:
       
       # mount -t iso9660 /dev/scd0 /mnt/cdrom/
       
       Then you can access the disk data via /mnt/cdrom/. Remember to umount
       the /mnt/cdrom/ if you want to access another one.
       
       # umount /mnt/cdrom/
       
   02. If you want listening the music CD, insert the disk into CD-ROM,
       then you do not need to mount like the data disk. Just open the
       CD Player(like KsCD in KDE..), then you can start listening the music.